Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Jersey City: What to Know First
Olympia Chimney liner and rebuild work in Jersey City typically runs $1,100 to $4,200 depending on liner material, flue height, and whether the masonry crown and top courses need repair at the same time. We’re an independent Olympia Chimney service provider (not affiliated with or authorized by the manufacturer), and most liner replacements are completed in a single day once parts are on site. Every job gets a camera inspection first, a written price before work starts, and a photo record when it’s done.
If you own a home in Jersey City with an Olympia Chimney stainless liner, flexible liner, or an older terra cotta system that’s now failing, this page tells you what actually goes wrong, what it costs to fix, and what documentation you should demand from any company you hire. Call (862) 272-3868 for a free estimate.
How Olympia Chimney Products Fail - and How We Fix Them
Olympia Chimney has supplied the Jersey City market for years with stainless liners, chase covers, and chimney caps. The failure patterns we see are consistent enough to name, and Corrine Halstead says the same thing after most camera inspections: “The camera doesn’t negotiate. Neither does creosote.”
- Olympia stainless rigid liners: seam separation at the joints after years of thermal cycling. Jersey City’s freeze-thaw swings put repeated stress on liner seams, especially in uninsulated exterior chimneys on the older brownstones near Hamilton Park. When the camera shows a separated seam, flue gas escapes into the chase or masonry cavity. We replace the affected section or the full liner, and we insulate the replacement where local conditions call for it, which the manufacturer’s generic install guide rarely addresses for this climate.
- Olympia flexible liners: kinking and tearing at the offset where the flue changes angle below the smoke chamber. Flexible liner is not rated for sharp bends, but plenty of Jersey City rowhomes have offsets that put a hard kink in the liner. We see tears at that kink within six to ten years. The fix is either a rigid offset section or a full replacement with a properly supported liner, and we photograph the completed run so you can see it’s not kinked.
- Olympia terra cotta flue tiles (pre-liner installations): spalling and cracked tile sections. Homes built before the 1980s in Jersey City often have original Olympia terra cotta tile liners. Spalling, where the tile face flakes off from heat and moisture, is the most common reason we rebuild. Cracked tiles in the flue mean heat and gas are reaching the masonry, which is a chimney fire risk. We rebuild the flue with a stainless liner sized to the appliance, not just a patch.
- Olympia chase covers and top plates: rust-through at the corners and screw points. The chase cover is the flat metal top on a factory-built chimney chase. We replace more rusted Olympia chase covers in Bergen-Lafayette and the Heights than any other Olympia component besides liners. Water gets in, ruins the insulation, and accelerates liner corrosion. A new stainless chase cover with a proper seal is usually a same-day fix when paired with the liner job.
- Improper connector sizing from previous installations. The connector is the pipe between the appliance and the chimney. We regularly find Olympia liners that were installed with undersized connectors by a previous contractor, which chokes the draft and causes backpuffing into the house. We size connectors to the appliance’s BTU rating and verify the draft with a reading before we call the job done.
Our Olympia Chimney Chimney Liner & Rebuild Process
Here’s what a liner or rebuild job looks like from the first call, because you should know before anyone shows up.
- 1
Call and schedule. A live person answers at (862) 272-3868. We schedule the inspection, not the repair. Price comes after evidence.
- 2
Camera inspection (NFPA 211 Level 2). We run a camera down the entire flue and show you the footage on site. You see what we see, including any Olympia-specific failure we find.
- 3
Written scope and price. We write down exactly what’s being replaced, what materials we’re using, and what it costs. You get this before any work starts, per Clause 1 of the Haven Standard.
- 4
Parts decision. If we’re replacing an Olympia liner, we walk through the OEM versus quality aftermarket trade-off. For most Jersey City applications, a DuraFlex or HeatShield liner does the same job at a better price, and we stand behind it with the same 365-Day Done Right Promise. If your preference is OEM Olympia, we source it and price it honestly.
- 5
The work. Liner removal, flue prep, new liner installation, and any crown, chase cover, or masonry rebuild needed. A named, background-checked technician is assigned to your job and you get a text when they’re on the way.
- 6
Post-work camera pass and documentation. We run the camera again after the install and hand you a photo record that includes before, during, and after images. You also get a written warranty. Nothing is left unshown.
Before
AfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Jersey City
Prices below reflect what we charge for Olympia Chimney liner and rebuild work in Jersey City as of 2026. Every price is written and fixed before work begins, no surprises.
- Stainless steel liner replacement (single flue, 25-35 ft): $1,100 - $1,900
- Flexible liner replacement (with offset, standard chase): $1,400 - $2,200
- Liner repair (sectional replacement or seam repair): $450 - $850
- Partial rebuild (top 10-15 courses plus new liner): $1,800 - $3,200
- Full chimney rebuild from the roofline up: $3,500 - $4,200+ depending on height, access, and masonry condition
What moves the price: flue height, roof pitch and access, whether the crown needs rebuilding in the same visit, and whether the old liner was properly supported. Bring us any competitor’s written estimate for a free second opinion on the price. Call (862) 272-3868.
Why Jersey City Homeowners Call Level Two Chimney Jersey City for Olympia Chimney Work
We’re not impressed by Olympia Chimney’s name, and you shouldn’t be either. A brand name on a liner matters less than whether it was installed correctly, documented, and warrantied. Since 2009, we’ve inspected over 38,000 chimneys and every single one got a written price before work started and a photo record when it was done. That’s the Haven Standard, and it’s not a marketing phrase. Clause 4 of the Haven Standard requires the camera documentation we’ve been doing since our first year in business.
Our techs know the difference between an Olympia seam failure and a bad install. We also work with DuraFlex, HeatShield, and Gelco liner systems, so we’re not pushing one brand. We recommend what the camera supports. Every job is backed by our 365-Day Done Right Promise: if it’s not done right, we make it right.
FAQs
The Olympia Chimney manufacturer’s warranty covers the liner material itself, not the labor to remove and replace a failed liner. Labor is almost always on the homeowner. Before you decide on a repair path, get the warranty terms in writing from wherever the original system was purchased, then call us for a camera inspection to document the failure with photos you can use for any claim. We’ll walk you through what the camera shows at (862) 272-3868.
Most Olympia Chimney liner replacements in Jersey City are completed in one day once the correct liner and parts are on site. Specialty sizes or OEM Olympia parts may add a few days to sourcing. Every job starts with the inspection, not the repair, so the first visit is diagnostic and you get the written price that same day.
For liner replacement, an aftermarket stainless liner from DuraFlex or HeatShield performs equivalently to OEM Olympia in most Jersey City applications, and we warranty the labor and the part with our 365-Day Done Right Promise. If you specifically want OEM Olympia parts, we source and install them at an honest price. The OEM-versus-aftermarket decision matters less than correct sizing, insulation, and installation, which is exactly what our camera inspection verifies.
Yes, if the camera shows isolated damage like a single separated joint or a small tear and the surrounding liner is structurally sound. Sectional repair runs $450 to $850 in Jersey City. If we see multiple failure points, corrosion, or kinking, we’ll tell you plainly that a full replacement is the honest fix, and we’ll show you the footage that supports that recommendation before any price is quoted.
A separated or torn liner lets heat and flue gas reach the masonry and framing, which is how chimney fires and carbon monoxide leaks start. In an older Jersey City rowhome, the surrounding masonry is often already compromised from years of water intrusion. The repair gets more expensive the longer it waits, and the hazard gets real. If you’re unsure what condition your Olympia liner is in, we’ll show you on camera and give you a written price, free of charge. Call (862) 272-3868 for an estimate.
Get a Written Price for Your Olympia Chimney Liner or Rebuild
If your Olympia Chimney liner is showing signs of failure, or if your Jersey City home has an older terra cotta flue that hasn’t been looked at in years, call Level Two Chimney Jersey City at (862) 272-3868. We’ll schedule the camera inspection, hand you a written price before any work starts, and you’ll have a documented photo record of everything we found and everything we did. Free estimate, no pressure, and a real person answers the phone.
Written by Corrine Halstead, Owner, Level Two Chimney Jersey City at Level Two Chimney Jersey City, serving Jersey City and nearby areas.